荔湾3-1气田调整开发项目调节阀国际招标澄清或变更公告(1)

正文内容

澄清或变更简要说明：原投标文件递交截止时间和开标时间变更为：****年*月**日*时（**时间)。 *************受招标人委托对下列产品及服务进行国际公开竞争性招标，于****-**-**在中国国际招标网发布变更公告。本次招标采用传统招标方式，现邀请合格投标人参加投标。 *、招标条件 项目概况:***-* 气田群位于中国*****盆地**凹陷内，距**东南 部***km，气田群所在海域水深***-****m。***-* 气田调整开发项目通过 降低***-* 气田群水下井口压力实现增产，无调整井及***台设施。平台增压部分在***-*CEP 平台*** 台预增压湿气压缩机、入口涤气罐及出口冷却器和* 台段塞流捕集器，改造凝析油增压泵。平台增压部分计划于****年* 月投用。 资金到位或资金来源落实情况:已落实 项目已具备招标条件的说明:已具备 *、招标内容 招标项目编号:****-****JDCP**** 招标项目名称:***-*气田调整开发项目调节阀 项目实施地点:中国**省 招标产品列表(主要设备): 序号 产品名称 数量 简要技术规格备注* 调节阀 ** 详见技术文件 *、投标人资格要求 投标人应具备的资格或业绩:对投标人的资格和业绩要求： Requirements for Qualification and reference of Bidder: （*）资格要求 Requirements for Qualification of Bidder A．★营业执照：如果投标人为境内注册公司，投标人需提供合法有效的企业法人营业执照、税务登记证及组织机构代码证或证照合一的营业执照；如果投标人为境外注册公司，需提供有效的公司登记注册证明。 A．★Business licence: The bidder within the customs territory shall provide valid independent legal person business license, tax registration certificate, organization code certificate, or combined certificate and business license;The bidder outside the customs territory shall provide valid certificate to prove valid business registration certificate. B．★制造商要求: 所投产品为国内产品：不允许代理商投标，投标人需是调节阀的制造商 所投产品为境外产品：允许调节阀的制造商或取得调节阀制造商唯一授权的代理商投标。 投标人为代理商时，应得到本次投标调节阀制造商的唯一合法授权，并需提供以下材料（盖制造商公章）： *）在有效期内的调节阀制造商授权书； *）调节阀制造商承诺函，承诺投标所投产品为制造商工厂生产。 B． ★ Manufacturer requirement: The product being bid for is a domestic product: agents are not allowed to bid, and bidders must be manufacturers of control valves. The product being tendered is an overseas product: manufacturers of control valves or agents authorized solely by the control valve manufacturer are allowed to bid. When the bidder is an agent or a contractor, they should obtain the sole legal authorization of the control valve manufacturer for this bidding and provide the following materials (stamped with the manufacturer's official seal): *) Authorization letter from the manufacturer of the control valve within its validity period; *) Commitment letter from the manufacturer of the control valve, promising that the products submitted for bidding will be produced by the manufacturer's factory. C．★是否接受联合体投标：否。 C. ★Joint Venture: Not Accepted. D．★未领购招标文件是否可以参加投标:不可以。 D. ★Bid without the bidding documents：NOT Available. （*）★资质要求及证明文件 投标人所供的阀门制造商应取得由国家*场监督管理总局颁发的特种设备生产许可证（许可子项目涵盖A*及A*）及覆盖本次招标范围的由第三方颁发的特种设备型式试验证书,投标人应在投标时提供上述证书的扫描件。 The manufacturers of pressure pipeline components such as valves provided by the bidder shall obtain the special equipment manufacturing license (TS A* or A* certificate) awarded by State Administration for Market Regulation and the special equipment type test certificate covering the scope of this bidding awarded by third party,Bidders should provide scanned copies of the aforementioned certificates during the bidding process. （*）★业绩要求Requirement for Bidder's reference: 投标人需满足以下所有要求： The Bidder needs to meet all below requirements： A.From January *, **** to the bidding deadline (based on the contract signing time), the control valve manufacturer submitted by the bidder must have at least * sets of pneumatic control valves and * sets of electric control valve matching supply performance. The brand and Production factory address of the control valve submitted by the bidder must be consistent with the performance of the control valve mentioned above(The Production factory address of valve PV-****D should be consistent with the performance Production factory address corresponding to performance requirement *, the Production factory address of other pneumatic control valves should be consistent with the performance Production factory addresss corresponding to performance requirement *, and the Production factory address of electric control valves should be consistent with the performance Production factory address corresponding to performance requirement *). The performance should meet or exceed the following technical requirements: Performance Requirement * Performance Requirement * Performance Requirement * pneumatic control valve pneumatic control valve electric control valve Performance requirement: * set Performance requirement: * set Performance requirement: * set body material A*** F** or A*** Gr.*A body material A*** Gr.*A body material A*** Gr.*A Body size ≥**” Body size ≥**” Body size ≥*” Body rating ≥****# Body rating ≥***# Body rating ≥***# Body type V-Ball or Globe Body type Globe Body type Globe Flow coefficient CV CV ≥ *** at minimum flow rate. CV ≥ ****under normal traffic conditions. CV ≥ **** at maximum flow rate. Flow coefficient CV CV ≥**.* at minimum flow rate. CV≥***under normal traffic conditions, CV≥***at maximum flow rate.. Flow coefficient CV CV ≥*.**at minimum flow rate.. CV≥** under normal traffic conditions. CV≥ ***at maximum flow rate.. Open sized **%-**% Open sized **%-**% Open sized **%-**% Bidders must submit a performance table for regulating valves in the prescribed format and provide relevant performance certification documents. The performance certification documents include but are not limited to: *) a copy of the sales contract and *) arrival acceptance materials signed or stamped by the user (arrival acceptance form or commissioning acceptance report or other valid proof materials that can prove that the goods under the contract have been received and accepted). The performance certification documents submitted by the bidder must at least reflect the following contents: contract signing time, contract signing page (domestic trade contracts should have both parties' seals, international trade contracts should have both parties' signatures or seals), manufacturer name, goods name, brand and production factory address, supply quantity, technical parameters/indicators (including at least valve body material, valve body class, valve body type, valve body type, CV value, valve allowable opening and calculation sheet), and arrival acceptance materials signed or stamped by the user. If the performance contract is an annual agreement, in addition to providing the annual agreement, corresponding received orders should also be provided, and the order content or number should be associated with the annual agreement. Providing one or more orders and corresponding arrival acceptance materials under the same annual agreement is considered as one valid performance. Failure to submit performance certification documents, or failure to meet the above performance requirements through the provided performance certification documents, shall be deemed as invalid performance. ****年*月*日至投标截止日（以合同签订时间为准），投标人所投调节阀的制造商必须至少有*台气动调节阀和*台电动调节阀配套供货业绩。投标人所投的调节阀的品牌和生产工厂地址必须与上述提交的业绩品牌和生产工厂地址保持一致（阀门PV-****D生产工厂地址应与业绩要求*对应的业绩生产工厂地址一致，其余气动调节阀生产工厂地址应与业绩要求*对应的业绩生产工厂地址一致，电动调节阀生产工厂地址应与业绩要求*对应的业绩生产工厂地址一致）。业绩中的技术指标应全部达到或超过以下技术要求： 业绩要求* 业绩要求* 业绩要求* 气动调节阀 气动调节阀 电动调节阀 业绩要求：*套 业绩要求：*套 业绩要求：*套 阀体材质 A*** F** 或A*** Gr.*A 阀体材质 A*** Gr.*A 阀体材质 A*** Gr.*A 阀体尺寸 ≥**” 阀体尺寸 ≥**” 阀体尺寸 ≥*” 阀体磅级 ≥****# 阀体磅级 ≥***# 阀体磅级 ≥***# 阀体类型 V-Ball 或 Globe 阀体类型 Globe 阀体类型 Globe 流量系数CV 最小流量的情况下CV ≥*** 正常流量的情况下CV≥**** 最大流量的情况下CV≥ **** 流量系数CV 最小流量的情况下CV ≥**.* 正常流量的情况下CV≥*** 最大流量的情况下CV≥ *** 流量系数CV 最小流量的情况下CV ≥*.** 正常流量的情况下CV≥** 最大流量的情况下CV≥ *** 开度 **%-**% 开度 **%-**% 开度 **%-**% 投标人须按规定格式提交调节阀业绩表，并提交相关业绩证明文件。业绩证明文件包括但不限于：*）销售合同复印件和*）用户签字或盖章的到货验收材料（到货验收单或调试验收报告或其他可以证明合同项下货物已经到货验收的有效证明材料）。投标人所提交的业绩证明文件必须至少体现以下内容：合同签署时间、合同签署页（国内贸易合同应有双方盖章，国际贸易合同应有双方签字或盖章）、制造商名称、货物名称、品牌及生产工厂地址、供货数量、技术参数/指标（至少包括阀体材质、阀体磅级、阀体尺寸、阀体类型、CV值、阀门允许开度及计算书）、用户签字或盖章的到货验收材料。若业绩合同为年度协议，除提供年度协议外，还应提供相应的已到货订单，订单内容或编号应与年度协议相关联。同一个年度协议下提供*个或以上的订单及与订单对应的到货验收材料均算为*个有效业绩。未提交业绩证明文件，或通过所提供的业绩证明文件无法认定满足上述业绩要求的，均视为无效业绩。 B.The brand of the actuator shall meet the requirements of Appendix A. Bidders may recommend other brands that meet the following conditions and are equivalent to the recommended brand in Appendix A. From January *, **** to the bidding deadline (based on the time of contract signing), the bidder or the manufacturer of the actuator submitted by the bidder shall have a performance of supplying no less than * regulating valves, and the brand and model of the actuator in the performance shall be consistent with the one used in this bidding. If the actuator is used on a pneumatic regulating valve, the material of the regulating valve body in the performance should be A***F**, the valve body size should be ≥ ** ", and the valve body pressure scale should be ≥ **** #; If the actuator is used on an electric regulating valve, the valve body material of the regulating valve in the performance should be A***F**, the valve body size should be ≥ * ", and the valve body pressure rating should be ≥ *** #. Bidders of other brands equivalent to the recommended brand must provide performance certification documents, ★The performance certification documents include but are not limited to: *) a copy of the sales contract and *) arrival acceptance materials signed or stamped by the user (arrival acceptance form or commissioning acceptance report or other valid proof materials that can prove that the goods under the contract have been received and accepted). The performance certification documents submitted by the bidder must at least reflect the following contents: contract signing time, contract signing page (domestic trade contracts should have both parties' seals, international trade contracts should have both parties' signatures or seals), manufacturer name, goods name, model and production factory address, supply quantity, technical parameters/indicators (including at least valve body material, valve body size,valve body class, valve body type), and arrival acceptance materials signed or stamped by the user. If the performance contract is an annual agreement, in addition to providing the annual agreement, corresponding received orders should also be provided, and the order content or number should be associated with the annual agreement. Providing one or more orders and corresponding arrival acceptance materials under the same annual agreement is considered as one valid performance. Failure to submit performance certification documents, or failure to meet the above performance requirements through the provided performance certification documents, shall be deemed as invalid performance.he brand of the actuator should meet the requirements of Appendix A. Bidders may recommend other brands that meet the following conditions and are of the same level as the recommended brand in Appendix A. From January *, **** to the bidding deadline (based on the contract signing time), the bidder shall have a performance of supplying no less than * sets/sets of regulating valves for key components of the same level brand. If the actuator is used on pneumatic regulating valves, the material of the regulating valve in the performance should be A***F**, size ≥ ** ", and pressure rating ≥ **** #; If the actuator is used on an electric control valve, the material of the control valve in the performance should be A***F**, size ≥ * ", pressure rating ≥ *** #. It is recommended that bidders of other brands in the same grade provide performance certification documents. The corresponding performance certification document requirements are detailed in the following performance requirements * and *; Performance Requirement * Copy of sales contract reflecting the recommended brand and model (including contract cover and signature page, as well as relevant technical attachments) Arrival acceptance materials (buyer's signed or stamped arrival acceptance form, on-site debugging report, usage certificate, or acceptance certificate) Performance Requirement * The performance certification documents submitted by the bidder must at least reflect the following contents: brand and production factory, technical parameters of supporting control valves, supply quantity, usage environment, technical parameters/indicators, and arrival acceptance materials. Failure to submit performance certification documents, or if the provided performance certification documents cannot verify the above content, shall be deemed as invalid performance. 执行机构的品牌应满足附录A要求，投标人可推荐满足以下条件与附录A或相当于推荐品牌的其它品牌。****年 * 月 * 日至投标截止日（以合同签署时间为准）投标人或投标人所投执行机构的制造商应具有不少于*台调节阀供货的业绩，且业绩中执行机构的品牌与型号应与本次投标所用的一致。若该执行机构使用在气动调节阀上，则业绩中的调节阀阀体的材质应为A***F**，阀体尺寸≥**”，阀体压力磅级≥****#；若该执行机构使用在电动调节阀上，则业绩中的调节阀的阀体材质应为A***F**，阀体尺寸≥*”，阀体压力磅级≥***#，推荐相当于推荐品牌的其它品牌的投标人须提供业绩证明文件， 业绩证明文件包括但不限于：*）销售合同复印件和*）用户签字或盖章的到货验收材料（到货验收单或调试验收报告或其他可以证明合同项下货物已经到货验收的有效证明材料）。投标人所提交的业绩证明文件必须至少体现以下内容：合同签署时间、合同签署页（国内贸易合同应有双方盖章，国际贸易合同应有双方签字或盖章）、制造商名称、货物名称、型号及生产工厂地址、供货数量、技术参数/指标（至少包括阀体材质、阀体尺寸、阀体磅级、阀体类型）、用户签字或盖章的到货验收材料。若业绩合同为年度协议，除提供年度协议外，还应提供相应的已到货订单，订单内容或编号应与年度协议相关联。同一个年度协议下提供*个或以上的订单及与订单对应的到货验收材料均算为*个有效业绩。未提交业绩证明文件，或通过所提供的业绩证明文件无法认定满足上述业绩要求的，均视为无效业绩。 是否接受联合体投标:不接受 未领购招标文件是否可以参加投标:不可以 *、招标文件的获取 招标文件领购开始时间:****-**-** 招标文件领购结束时间:****-**-** 是否在线售卖标书:否 获取招标文件方式:现场领购 招标文件领购地点：有兴趣的投标人可通过以下方式获取招标文件请登录中国海油供应链数字化平台(https://bid.cnooc.com.cn）的招标公告页面进行购买。首次登录必须先进行注册（免费），注册成功后，方可购买招标文件。投标人须在线填写购买招标文件登记表，并在线支付标书款，支付成功后，投标人可自行下载招标文件。 招标文件售价:￥***/$** 其他说明:对于使用美元购买招标文件的投标人，需电汇至以下账号：收款人：*************，收款行名称：INDUSTRIAL AND COMMERCIAL BANK OF CHINA,Beijing National Cultural and Financial Cooperation Demonstration Zone Jinjie Sub-branch，收款人账号：*******************，SWIFT CODE: ICBKCNBJBJM，收款行地址：No. *** Wang fu jing Street, Dong cheng District, Beijing, China PR: ******。 *、投标文件的递交 投标截止时间（开标时间）:****-**-** **:** 投标文件送达地点:******东三环北路甲*号京信大厦**层 开标地点:******东三环北路甲*号京信大厦**层 *、联系方式 招标人:中海石油（中国）有限公司 地址:**省******后海滨路****号海洋石油大厦A座**层 联系人:熊超 联系方式:+**-***-******** 招标代理机构:************* 地址:******东直门外小街*号海油大厦*层 联系人:刘森 联系方式:+** ***-******** *、汇款方式: 招标代理机构开户银行(人民币): 招标代理机构开户银行(美元): 账号(人民币): 账号(美元): *、其他补充说明 附件：附件.zip